ADDRESS

wiseWood veneer ++ 5490 Gatewood Dr. ++ Sterling Heights, MI 48310 ++ Toll free: 855.883.6337 (855.8VENEER)
Local: 586.825.2387 ++ Fax: 586.825.2390 ++ choose@wisewoodveneer.com
Showing posts with label how to. Show all posts
Showing posts with label how to. Show all posts

August 8, 2012

Introducing the WiseWood Veneer Cabinet Refacing Kits

We would like to end our long absence from this blog with an introduction to a whole new product line from WiseWood Veneer. We now offer cabinet refacing kits. Perfect for professionals and do it yourselfers. We have taken care to include everything that you would need to reface kitchen cabinets, bathroom vanities, or other types of furniture. Unless the remodel project calls for a change in size or a reconfiguration of the cabinet layout, the cabinets are (in most cases) just fine and do not need replacing. A change in appearance is what most people are after and this is where a cabinet refacing kit comes in handy.


The kits come in 3 different sizes and are an economical way to give your cabinets a face lift and a new look. Re-facing is a lower cost alternative to a complete tear out and reinstallation of new cabinets. Also it can be done in a fraction of the time at fraction of the cost. Available in the most popular species such as cherry, maple, mahogany and walnut, the kits come with veneer and edgebanding of your choice, a veneer scraper, a utility knife, a tack cloth, sandpaper and a sanding block. Detailed and comprehensive step by step instructions are also included.


Each veneer sheet is backed with 3M™ pressure sensitive adhesive which simplifies the application process. The edgebanding is pre glued with a hot melt adhesive which is easily applied with a household iron. Both, the veneer and edgebanding will accept stains and finishes so you can customize and match colors to give your cabinets the exact look you want. With 3 different sized kits you can get the appropriate kit for the size of your project. However, if you run short on veneer or edgebanding you can always buy 2’ x 8’ PSA (pressure sensitive adhesive) backed veneer sheets individually and edge banding in small 50’ rolls separately.


Below is an excerpt of the cabinet refacing instructions but you can also download them in a PDF file. We would love to hear from you if you happen to have any questions or comments whether by phone [(586) 825 2387] or by email [info@wisewoodveneer.com]. We are always here to help if you happen to run into trouble.


Cabinet Refacing Instructions

For Face Frame Cabinets

For the purpose of describing only the cabinet refacing process we have left out any reference to replacement of doors and drawer fronts. Although this is also a major part of any refacing project the options are numerous and can be better dealt with by those companies that sell replacement doors and fronts.


Prepare Cabinets Boxes For Refacing (excerpt)

• Remove doors and hinges. If planning to re-use any hardware keep hinges and screws together in a safe place.

• Remove any trim molding by using a stiff putty knife or small tack puller under the edge of the molding and gently pry loose.

• Remove complete drawer boxes and set aside in a safe area.

• Now you’re down to cabinet boxes only. Inspect frames for any loose or peeling surfaces and repair these as well as any deep dents or scratches. These can be filled with wood putty or even better, auto body filler (Bondo) and sanded smooth.

• Lightly hand sand all surfaces with 120 grit sandpaper and a sanding block. You just want to “scuff” the surface, not completely remove the finish down to bare wood. Don’t use a power sander for this purpose.

• Wipe down all surfaces with a mild detergent and water solution or a mild solvent like denatured alcohol. Use a damp cloth only so as not to soak or saturate the wood and allow ample drying time. After surfaces are completely dry wipe with a tack cloth to remove any remaining dust or particles.


Veneering End Panels

• Your kit comes with 2 different types of veneer, sheet veneer with a PSA (pressure sensitive adhesive) backing and rolled edge banding with a hot melt adhesive backing.

• You will start veneering cabinets by first applying PSA veneer to any exposed end panels. The wood edge banding will be used on the inside edges of the face frames around door and drawer openings.

• For the end panels take careful measurements for height and width. Cut the veneer width to the exact size and cut the height about an inch oversized using a good square and straight edge. Usually the face frames on cabinets extend an 1/8” or so beyond the cabinet end panel so you’ll be fitting this veneer between the backside of the face frame and the wall. By leaving the tall dimension of the veneer extra long you’ll have some free play when trying to align and place this end piece. After the veneer has been cut to fit this panel you will want to dry fit it before removing the release paper and exposing the PSA glue surface. The face frame overlap gives you a good edge to register the veneer against. When you’re satisfied with the fit you are ready to move on to the next step and apply the veneer.

• Peel away a few inches of release paper on the front edge to expose the adhesive. Register the veneer to the top or bottom of the end panel and butt up tight to back of the face frame. With the veneer placed where you want it, apply light pressure by hand to the surface along the leading edge where you’ve exposed the glue surface to effectively anchor the piece and prevent movement. Now you can reach behind with one hand to pull back the release paper while smoothing the veneer surface with the other hand as you go. With the veneer firmly affixed, smooth with the veneer scraper while applying downward pressure, moving in the same direction as the grain.

• Inspect the surface for any bubbles or loose edges. If any of these conditions exist go back over these areas with the veneer scraper.

• Repeat this process on any exposed cabinet ends. Instructions continued here.


PDF version of these instructions

WiseWood Veneer

October 26, 2011

You Need to Veneer Something and You Have to Use Contact Cement

You have a project, you want to use paper backed wood veneer, and you have to use contact cement. Can it be done? How? The quick answer is yes, it can be done. It can be done by you and it can be done successfully. The key is to consider and prepare for all the potential pitfalls that arise with a flexible glue line. To apply flexible wood veneer with contact cement is not difficult but the method is meticulous and there are no short cuts. Below you can find comprehensive instructions for adhering paperbacked veneer with contact cement. On large projects or full size panel layups this method can be very labor intensive.

Applying wood veneer with contact cement is an acceptable method when other methods aren’t available or practical. By following these established practices and recommendations you will have good success using contact cement with 20mil paperbacked, wood backed and phenolic resin backed wood veneer. Do not use contact cement to adhere raw or unbacked wood veneers.



Wood Veneer Application When Using Contact Cement


Preparation
When you receive your veneer you must allow time for it to acclimate to your environment prior to use. To accomplish this it’s necessary to remove the veneer from the packaging and lay it flat for a minimum of 48 hours up to 4 days. It may be necessary to apply some weight on the ends of the sheet to help retain flatness during this period. The ideal environment for this process is between 35% and 50% relative humidity and temperature levels between 65 to 80 degrees F. It is also important to allow your substrate material to acclimate in the same conditions for the same amount of time as the veneer. This will ensure that materials will be relatively equal in terms of relative moisture and temperature. It’s best to plan ahead if possible and avoid veneering when conditions of high humidity or extreme dry conditions are expected.

Adhesives for Wood Veneer
Solvent based contact adhesives work best for wood veneering with our products. When it is necessary to use water based adhesives you may want to consider using a phenolic resin backed wood veneer. Before using any adhesive be sure it is at room temperature and properly mixed as the solids which create the bond strength tend to settle much like pigment in paint. Brush or roller grade adhesives are best to achieve 100% coverage on all surface areas. Spray grade adhesives can be used but you must be sure you get 100% surface coverage. It’s necessary to coat both surfaces that are to be bonded. It’s not always necessary but on some smooth glossy surfaces it will help bond strength if you scuff sand the surface with 120 grit sandpaper prior to glue application. If the substrate is “open” or “porous” it will require a second application of glue as the first coat will partially absorb into the surface. This is most likely to occur when using plywood as your substrate. All contact cements require time for the solvents to “flash off” before the two surfaces can be mated together. This period, referred to as “open time” will be specified by the manufacturer and should be adhered to. Extreme conditions such as high heat, high humidity, low temperatures etc., can effect the open time so some discretion must be used under these conditions. It is important to understand and follow the adhesive manufacturer’s recommendations on application of their product.

Tools and Supplies for Wood Veneering
There are a few basic supplies and tools to have ready before you veneer. You will need a good quality contact cement, small roller or brush for glue application, a veneer scraper or smoothing tool and separator strips. Veneer scrapers can be purchased commercially and typically consist of a wooden handle and a stiff blade of polycarbonate or lexan about 4” wide. You can also make one by using a piece of hardwood approximately 4” wide by 12 to 16” in length. Make sure one end is cut nice and straight and use sandpaper to gently ease the corners and edge to eliminate any sharp lines. If you want you can also contour the upper portion of the handle to create a comfortable grip. With this smoothing blade you will generate excellent leverage and good pressure on the surface. The separator strips can be pieces of hardwood, MDF or hardboard or some people use wooden dowels. They should be long enough to span the width of the piece you are veneering. We don’t advocate the use of any type of J-roller for veneer application. You will not generate enough pressure with any type of J-roller.

READ THE COMPLETE INSTRUCTIONS HERE.


At WiseWood Veneer we have all the popular domestic, exotic, and reconstituted wood veneer species in stock on FlexVen™ 10 (10mil), FlexVen™ 20 (20 mil), and Tuf-Pli™ (polyback or phenolic) backed flexible wood veneers.

June 9, 2011

How to apply pressure sensitive adhesive (PSA) backed veneer.

If you have ever wondered what it takes to successfully apply pressure sensitive adhesive backed wood veneer, below you'll find comprehensive instructions to do just that. Pressure sensitive adhesive (PSA) is very thin acrylic based film applied to 10mil paper backed flexible wood veneer sheets. It is often referred to as "peel and stick" veneer. In recent years this method of applying wood veneer has gained much popularity with professionals and do it yourselfers because of its relative ease of use and no mess application. It also eliminates the need for a hot press and/ or vacuum bag and allows the veneer to be adhered to more nontraditional substrates such as steel and plastic. Although the wood veneer is available in 2' x 8', 4' x 8', and even 4' x 10' sheets the PSA method of application is not very practical for veneering full size panels. PSA wood veneer is easy to apply but it can become very labor intensive especially on large projects with vast surface areas and there are steps to the application that are meticulous. Namely, making sure that every square inch of the surface area has had enough pressure applied to it.



PSA Veneer Application Instructions


Preparation
When you first receive your veneer inspect it thoroughly for satisfaction of grade and quality prior to lamination. Next it’s very important to allow your veneer to acclimate prior to use. This is done by laying the veneer flat on a surface and allowing it to “relax” in your environment for a minimum of 48 hours up to 4 days. It may be necessary to apply some weight on the ends of the sheet to help retain its flatness during this period. The ideal environment for this process is between 35% and 50% relative humidity and temperature levels between 65 to 80 degrees F. It is also important to allow your substrate material to acclimate in the same conditions for the same amount of time as the veneer. This will ensure that materials will be relatively equal in terms of relative moisture and temperature.

Tools and Supplies
Before starting your veneering project you’ll want to gather some basic tools and supplies. You will need 120 grit sandpaper, tack cloth, denatured alcohol, a sharp utility or exacto knife and a veneer scraper. Veneer scrapers can be purchased commercially and typically consist of a wooden handle and a stiff blade of polycarbonate or lexan about 4” wide. You can also make one by using a piece of hardwood approximately 4” wide by 12 to 16” in length. Make sure one end is cut nice and straight and use sandpaper to gently ease the corners and edge to eliminate any sharp lines. If you want you can also contour the upper portion of the handle to create a comfortable grip. With this smoothing blade you will generate excellent leverage and good pressure on the surface. We don’t advocate the use of any type of J-roller for veneer application. You will not generate enough pressure with any type of J-roller.

Surface Preparation
Your substrate, or the surface you are going to laminate, needs to be prepped prior to veneering with PSA veneer. For finished surfaces you will need to scuff sand the entire surface with a medium (120 grit) sandpaper. After sanding remove all sanding dust and residue with tack cloth and wipe the surface clean with denatured alcohol. If you plan to veneer on an unfinished wood surface or plywood it is recommended that you first seal the surface with a coat of varnish, shellac or polyurethane finish. Allow the finish ample drying time, usually 24 hours, and then continue on with the veneer application.

READ THE COMPLETE INSTRUCTIONS HERE.


At WiseWood Veneer we have several popular species with PSA already in stock and we have the capability to apply the adhesive backer to any of our FlexVen™ 10 and FlexVen™ 20 backed flexible wood veneers.