wiseWood veneer ++ 5490 Gatewood Dr. ++ Sterling Heights, MI 48310 ++ Toll free: 855.883.6337 (855.8VENEER)
Local: 586.825.2387 ++ Fax: 586.825.2390 ++

April 3, 2012

How To Use Iron On Edgebanding

Wood edgebanding is a great way to put the final touches on your veneer project. It is easy to use, covers the edges of your substrate and gives your project uniformity and the appearance of solid material. It is available in virtually every wood species and almost any size. Whether your project is made with exotic or domestic veneer species we can offer you a Pre Glued or Iron On edgebanding to match. Edgebanding can also offer other aesthetic and creative opportunities for your furniture or kitchen designs that might not be practical with solid wood material. Some designers like to use contrasting color and/ or wood species edgebanding on the edges of doors and drawers to create bold and dramatic lines in their designs.

Iron On edgebanding is very simple to use whether you have an edgebander for production runs or you are just using a household iron to apply it. Below you will find our comprehensive instruction for using Pre Glued edgebanding. And through the month of April we are offering a 10% discount on all our in stock Pre Glued and Fleeceback edgebanding.

Iron on Edge Banding Application

Tools and Supplies
Working with iron on edge banding isn’t hard and doesn’t require any specialized tools or skills. Most of the tools you will need can be found in almost any home. You will want a standard household iron, an edge trimmer or standard utility knife or razor knife. We suggest you dedicate an iron for this purpose only as you may get some glue “squeeze out” when applying the edgeband. A small travel size iron offers better control than a standard iron.

Getting Started
Whether the edges to be covered are MDF, plywood or particle board, be sure that any deep saw marks are smoothed and any voids filled. Your iron should be set on a medium heat setting. A high setting is not necessary because the hot melt adhesive on the edge banding has a low melting point. The possibility of scorching the surface of the edge banding is also significantly reduced at this lower setting. Cut your edge banding about ½” longer than the edge to be banded. Also note that rolled edge banding has finger joints, or splice joints, typically every 4’-6’. A little pre-planning will help you to work around these joints if they are too noticeable or happen to be in a high visibility area. Starting at one end, position the edgeband with one hand and apply heat and downward pressure with the iron. We recommend doing 4” to 6” first and allow it to cool which will take approximately a minute. Now that the adhesive has cooled you have effectively “anchored” the strip which will make it easier to apply the remainder of the strip. Now you can move the iron steadily along the length of the edge while applying downward pressure with the iron. Normally you will exert enough pressure with the iron but you should check to make sure all the surface area is firmly sealed down. If you discover loose spots or edges that may want to curl up then you can re-heat the area and immediately apply pressure with a wood block, veneer scraper or flat edge tool to ensure a proper bond. Always apply the edgeband on the most visible surfaces last. By applying the most visible surfaces last you will ensure that any adjoining edges that butt up to this edge will be covered or over-lapped and therefore will be less visible.

Trimming the Edge Banding
Edge banding can be trimmed with a sharp utility or razor knife, a sharp wood chisel or a commercially available flush trimming tool. Good results can be achieved with any of these methods. To trim the excess length from a strip of wood edge banding simply cut with a utility knife or razor knife back to the panel end. Cutting across the wood grain like this is best accomplished using 2 or 3 scoring cuts instead of cutting through with one heavy stroke. This will help avoid any grain tear out, especially with coarse grained woods like red oak, hickory, white ash and some others. For trimming the excess from the edges use a sharp knife edge or sharp chisel held at a slight angle, not perpendicular, to avoid gouging or scarring the adjoining surface. For best control use short strokes with your knife or chisel blade. Don’t be concerned if you leave a little excess as this will be taken care of in the final step. If you are using a flush trimming tool press the edge of the tool firmly against the face of your panel and slide it along the edge to trim the excess edge banding. Working with the grain direction instead of against the grain will produce a cleaner cut with minimal grain tear out.

Finishing Up
To give your project that finishing touch use a sanding block with 120 grit abrasive. Sand any excess edge banding with this block skewed at an angle to produce a slight beveled edge. Run your fingers along this edge to check for any sharp edges or loose grain that could snag and tear out. Allow 24 hours before staining or finishing.

PDF version of these instructions

WiseWood Veneer


  1. Great information you have shared here. I hope you can make further research on how these things can help our industry. I enjoyed this and I found it interesting! Good job. - Chandler dentist

  2. Thanks for sharing the interesting piece of information, your post is simple yet smart. I have gone through all your posts and got a lot of experience.

    Veneered MDF | MDF with Veneers